other
  • VFFS Machines for Frozen Food: Packaging That Survives the Freezer
    VFFS Machines for Frozen Food: Packaging That Survives the Freezer
    Frozen vegetables, dumplings, seafood and ready meals place brutal demands on packaging. The film must stay flexible at −18°C, seals must survive ice crystals, and the machine itself must resist condensation in a cold room. A VFFS machine for frozen food is not the same machine as one for dry snacks — and Link Machinery’s 30 years of manufacturing experience shows in the differences. The Challenges of Frozen Food Packaging Moisture and ice crystals attack the seal area, causing micro-leaks Brittle film at low temperature cracks at the forming tube Condensation corrodes unprotected frames and electronics Sharp product edges such as fish bones and vegetable stems puncture thin film Machine Features That Matter Link builds frozen-food VFFS lines with low-temperature sealing film capability, stronger seal jaws with servo pressure control, and full stainless steel contact surfaces. The film path is designed for thicker, puncture-resistant laminates, and the frame is protected against wash-down and condensation. Optional nitrogen flushing extends shelf life for premium frozen products. Output and Integration Depending on bag size and film, a Link frozen-food VFFS line runs 30–80 bags per minute, synchronized with multi-head weighers or volumetric fillers and metal detectors. Contact the Link Machinery team with your product, bag size and freezer conditions, and we will recommend the right VFFS configuration for your frozen food line.
  • Anti-Drip Technology in Liquid Filling: Stop Waste and Messy Pouches
    Anti-Drip Technology in Liquid Filling: Stop Waste and Messy Pouches
    Drips are the hidden cost of liquid packaging. Every drop that trails from the nozzle between cycles lands on the film, weakens the seal and wastes product. Anti-drip technology stops that trail before it starts — and it is one of the details Link Machinery has perfected over 30 years of manufacturing experience. Why Liquids Drip Surface tension and residual product keep a film of liquid on the nozzle tip after each fill. When the nozzle lifts, that film stretches and falls. Viscous products like honey drip slowly; thin products like water drip instantly. Three Anti-Drip Solutions We Build Into Our Machines Suck-back function: the pump reverses briefly after dosing, pulling the liquid column back into the nozzle Spring-loaded cut-off nozzles: the valve closes mechanically the moment filling stops, shearing the droplet Heated and coated tips: temperature control keeps honey flowing, while food-grade coatings reduce adhesion The Result on Your Line Clean film means strong, leak-free seals and fewer rejected pouches. Operators spend less time wiping nozzles, and product loss drops to near zero. For producers filling honey, sauce, oil or juice into sachets and pouches, an anti-drip nozzle system directly improves yield. Link’s liquid filling machines combine piston pumps, anti-drip nozzles and PLC control in one integrated unit. Contact the Link Machinery team for a drip-free trial with your own product.
  • Screw Metering Accuracy: How Auger Fillers Keep Powder Weights Precise
    Screw Metering Accuracy: How Auger Fillers Keep Powder Weights Precise
    When a powder packing line runs at 40 bags per minute, every gram counts. Screw metering is the technology that keeps those grams consistent — a rotating auger inside a filling tube doses the powder by screw rotation, not by guesswork. Link Machinery has refined this dosing method over 30 years of manufacturing experience, and it remains the most economical way to fill powders, granules and spice blends into bags. How Screw Metering Works An auger filler uses a motor-driven screw (auger) inside a precisely machined tube. Each full rotation pushes a fixed volume of powder toward the bag opening. The weight of that volume depends on the screw pitch, the rotation speed and the powder’s density. By controlling the number and fraction of rotations, the machine delivers a repeatable dose every cycle. What Affects Filling Accuracy Powder density changes with humidity — a sealed, temperature-stable hopper reduces variation Bridging and caking stop powder flowing evenly — Link adds agitators and anti-bridging paddles Servo drive response — a servo-controlled auger stops within milliseconds for ±1–2% accuracy Tube clearance — worn screws create backflow, so Link machines use hardened stainless augers Why Accuracy Matters on a Packaging Line Underweight bags trigger giveaway and legal risk; overweight bags waste expensive product. On a 50-gram bag running 24/7, a 1-gram error costs thousands of dollars a month. Precision screw metering pays for itself quickly. Every Link automatic powder packing machine is assembled, tested and calibrated in our own factory before shipment. Contact the Link Machinery team to size a screw metering system for your product.
  • Why Custom Logo Packing is the Future of Bubble Tea Business
    Why Custom Logo Packing is the Future of Bubble Tea Business
    Bubble tea is one of the fastest-growing beverage categories worldwide, and competition is fierce. Custom logo packing — your brand name printed on every sachet and pouch — is how growing chains and suppliers differentiate themselves. Link Machinery makes private-label packing practical and affordable. A compact packing machine lets growing brands start with a single product line. Why Custom Logo Packing Matters Brand recognition: every serving carries your logo, building awareness with every cup sold Consumer trust: professional packaging signals quality and food safety Retail-ready: custom-packed ingredients are accepted by distributors and retail chains Differentiation: stand out from unbranded suppliers in a crowded market What Bubble Tea Businesses Pack with Link Machines Link automatic sachet and pouch packing machines handle the ingredients bubble tea brands pack in-house or co-pack: milk tea powder, sugar syrup, honey, fruit syrup, jelly cubes, popping boba and seasoning sachets. Each can be packed with your custom logo, weight and ingredient information printed directly on the film. How It Works 1. Design. Your artwork is prepared as print-ready film. Link supports your film supplier with machine specifications for correct registration. 2. Print. Custom-printed film is loaded onto the machine; photo-electric registration aligns every bag to the design. 3. Pack. The machine forms, fills, seals and cuts pouches or sachets with your logo on every single unit, at speeds up to 60–120 bags per minute. 4. Scale. Start with one product and expand to a full range with stored recipes and quick changeovers. Getting Started Link Machinery supports bubble tea suppliers with machine selection, film guidance, sample runs and after-sales service. Many of our customers started with a single sachet machine and grew into complete packing departments. Contact Link Machinery to discuss your custom logo packing project.
  • Precision Sealing: Resolving Leakage Issues in Liquid Packaging
    Precision Sealing: Resolving Leakage Issues in Liquid Packaging
    Leakage is the most common complaint on liquid packaging lines — and almost always preventable. At Link Machinery, precision sealing starts with understanding the three variables that control every seal: temperature, pressure and dwell time. On any liquid packing machine, sealing consistency determines product quality. Why Liquid Pouches Leak Liquid products put stress on seals from the inside: product splashes the seal area during filling, and internal pressure builds during handling. Common causes of leakage include contaminated seal zones, low sealing temperature, misaligned jaws, and film with poor sealant layers. Link's Precision Sealing System Accurate temperature control: servo-stabilized heating keeps jaw temperature within a narrow band, avoiding weak or burnt seals Balanced jaw pressure: pneumatic pressure set per film grade, applied evenly across the full seal width Dwell time control: sealing time synchronized with line speed for consistent seal strength Anti-drip dosing: clean nozzle cut-off keeps the seal zone free of liquid residue Sanitary jaw design: easy-cleaning jaws with non-stick coating reduce contamination build-up Practical Fixes for Leaking Seals 1. Raise temperature step by step. Increase by 5–10°C and run a leak test; stop at the lowest setting that seals reliably. 2. Check jaw alignment daily. Misaligned jaws cause weak or partial seals — inspect and adjust before every shift. 3. Verify film quality. The sealant layer must match your product and machine settings; test new film lots before production. 4. Keep the seal zone dry. Install anti-drip nozzles and check the dosing cut-off regularly. Proven Results On honey, sauce and juice pouch lines, Link machines hold seal integrity through pressure tests and long-distance shipping, with leakage rates reduced to near zero when the above parameters are applied. Contact the Link Machinery team for a sealing parameter sheet matched to your film and product.
  • How to Prevent Film Jamming in Automatic Sachet Machines
    How to Prevent Film Jamming in Automatic Sachet Machines
    Film jamming is one of the most common causes of downtime on automatic sachet machines. Most jams share the same root causes, and most can be prevented with simple checks. Here is the practical troubleshooting guide from Link Machinery’s service team. These checks apply to any automatic packing machine running flexible film. 1. Control Film Tension Too much tension stretches the film and causes registration drift; too little creates wrinkles and misalignment at the forming tube. Set the film dancer and brake according to the manual, and re-check when changing to a new film roll or material. 2. Check Roll Alignment and Splices A misaligned film roll walks sideways and jams at the forming collar. Mount the roll squarely, and never use a splice with bulky tape — splices must be thin, straight and positioned cleanly as they pass the forming tube. 3. Set Sealing Temperature Correctly Overheating melts film onto the sealing jaws; underheating leaves sticky, half-sealed film that wraps around the jaw. Confirm the correct temperature for your film grade and re-verify after material changes. 4. Keep the Forming Tube Clean Dust, static and product residue on the forming tube increase friction and cause sticking. Wipe the tube regularly and use a static eliminator in dry climates. 5. Routine Maintenance Lubricate the sealing jaw guides, inspect the cutter blades and check the film-path rollers for wear. A 15-minute daily inspection prevents most jams before they stop the line. If a Jam Occurs Stop the machine, isolate power, open the guards and carefully remove the jammed film — never pull film while the jaws are hot. Inspect the cause, correct it, and restart with a short test run. Follow these steps and your Link automatic sachet machine will run long, jam-free shifts.
  • Choosing the Right Film Material for Biodegradable Sachet Packing
    Choosing the Right Film Material for Biodegradable Sachet Packing
    Sustainability targets are pushing more brands toward biodegradable and compostable sachet packaging. But biodegradable films behave differently on the machine: they have different melting ranges, stiffness and sealing windows. This guide helps you choose the right material for reliable runs on Link automatic sachet machines. Whether you run a new packing machine or an existing line, film choice drives both cost and seal quality. Key Material Families PLA (polylactic acid): compostable under industrial conditions; good clarity but a narrow sealing window PBAT blends: flexible and tough, often blended with PLA or starch for better processability Starch-based films: cost-effective renewable content, sensitive to humidity Paper-laminated compostable films: premium look with a compostable barrier layer What to Check Before Buying Film 1. Sealing temperature range. Biodegradable films typically seal at lower temperatures and shorter dwell times. Confirm the material’s sealing window fits your machine’s heating system. 2. Moisture sensitivity. Many bio-films absorb humidity, which changes their stiffness and print registration. Store film in dry conditions and check the production room climate. 3. Print and registration. Softer bio-films can stretch under tension; use servo-driven film pull with accurate tension control — standard on Link machines — to keep registration stable. 4. Certification. Verify the film’s compostability certification (industrial or home) and confirm the certificate matches your market claims. Machine Considerations Link automatic sachet machines handle a wide range of bio-films with adjustable sealing temperature, pressure and dwell time stored as recipes. A quick trial run on your material is the fastest way to lock in the right settings — Link supports material tests at the factory before your line goes into production. Contact Link Machinery to test your biodegradable film on our sachet machines.
  • Smart Integration: Connecting Packaging Machines to ERP Systems
    Smart Integration: Connecting Packaging Machines to ERP Systems
    Modern packaging lines generate valuable data: bag counts, run speeds, downtime events and material usage. Connecting Link Machinery packaging machines to your ERP or MES system turns that data into decisions — live output tracking, accurate costing and full traceability. What Connectivity Delivers Real-time production data: bag count, speed, rejects and runtime stream to the ERP dashboard OEE tracking: availability, performance and quality calculated automatically Traceability: batch and date-code data linked to production records Predictive maintenance: alarm and wear data supports scheduled maintenance Material tracking: film and packaging material consumption monitored per order How Link Machines Connect Link packaging machines are built around PLC controllers with industrial communication interfaces. Standard integration options include OPC UA and Modbus TCP gateways, enabling secure connection to ERP and MES platforms without custom programming. For turnkey projects, Link engineers configure the data mapping and dashboards on site. Integration Scenarios 1. Order-driven production. The ERP downloads the order plan to the machine; recipes are selected automatically when a new batch starts. 2. Live reporting. Operators and managers see real-time output on the shop floor display and in the office dashboard. 3. Quality records. Every batch stores fill weights, seal temperatures and reject counts for audit and recall readiness. Getting Started Start with a simple data export from the machine PLC, then add two-way control as your team gains confidence. Link Machinery supports every stage, from a single data-collection pilot to a fully integrated smart packaging line. Ask the Link Machinery team how to connect your packaging line to your ERP system.
1 ... 15 16 17 18

A total of 18 pages

Leave A Message
Leave A Message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.

Home

Products

whatsapp